Skip to main content

We've Moved!

Product Documentation has moved to docs.hitachivantara.com
Hitachi Vantara Knowledge

Physical SVP hardware description

The physical SVP is provided by Hitachi Vantara. The physical SVP is a 1U management server that attaches to each VSP disk controller (DKC). The front and rear panels of the Hitachi-supplied physical SVP, along with the physical SVP specifications, are described.

SVP front panel

The front panel of the physical SVP is equipped with LEDs, a reset button, and a power button.

GUID-BD4A9A06-ADA2-4F32-A1E1-CF42F46814DF-low.png

Number

Description

1

LEDs. From left to right, the LEDs are:

  • BMC Heartbeat
  • LAN card 2
  • LAN card 1
  • Hard drive
  • System standby power
2

Reset button.

3

Power button. Applies power to or removes power from the SVP.

SVP rear panel

The only ports used on the rear panel of the physical SVP are the power socket and the four LAN ports.

GUID-20FC5D30-6EBA-4C6A-9E4C-EEBB2EE6AB29-low.jpg

Number

Description

1

Power socket. Attach the power cable supplied with the SVP.

2

Four LAN ports arranged as follows:

LAN3 LAN4

LAN1 LAN2

These ports connect to your IP network, the management console PC, and the user LAN port on each storage system controller.

NoteAfter the Initial Startup Wizard is run, the SVP can be used in non-bridge mode. In this mode, the cables can be removed from SVP ports LAN3 and LAN4 and attached to switches. For more information, contact customer support.

Service processor hardware specifications

The following table lists the hardware specifications for the service processor (SVP) provided by Hitachi Vantara.

CautionThe SVP is not supported in high-temperature environments. Do not operate it in locations where the temperature is 40°C or higher.

Item

Specification

Dimensions

Height: 1.7 inches (43 mm)

Width: 17.2 inches (437 mm)

Depth: 14.5 inches (369 mm)

Weight: 14 lbs (6.4 kg)

Processor

Celeron G1820 2.7-GHz 2M, 2C, 2T

  • Cores: 2

  • Instruction set: 64-bit

  • SmartCache: 2 MB

  • Maximum memory size: 32 GB

  • Memory types: DDR3-1333, DDR3L-1333 @ 1.5V

Memory

8-GB RAM DDR3

Hard drive

2 TB

Network interface card

x4 ports (on-board NIC) +

x1 IPMI (BMC) port

Fans

2 x 4-cm 4-pin PWM fans

Operating system

Windows Embedded Standard 7

Manufacturer

Super Micro (through Synnex)

Physical SVP electrical specifications

The following table lists the electrical specifications for the physical SVP supplied by Hitachi Vantara.

Item

Specification

Rated AC voltage

100-240 V, 50-60 Hz, 4.2 - 1.8A

Power supply

350-Watt AC power supply with PFC

AC voltage

100-240 V, 50-60 Hz, 4.2 - 1.8 Amp

Power supply safety / EMC

  • USA - UL listed, FCC
  • Canada - CUL listed
  • Germany - TUV Certified
  • Europe/CE Mark
  • EN 60950/IEC 60950-Compliant

MFT p-code

Description

Watts

MBD-X10SLM+-LN4F-O

Single-socket H3 (LGA 1150) / 32-GB DDR3 ECC 1600 MHz / 6x SATA / 4x GbE

20

CSE-512F-350B

Two 350 W 3.5-inch internal drive bays

26.4

CM8064601483405

Intel Celeron G1820 2.7 Ghz 2M tray

53

0F11000

3.5-inch 25.4 mm 2 TB 32 MB 7200 RPM

9.1

KVR16E11S8

4 GB 1600 Mhz DIMM SR x8 with TS Kingston F

4.05

112.55 Watts total

VA is 140.69, with a 0.8 power factor.

NoteThe measurements are not kilo values.

Physical SVP environmental specifications

The following table lists the environmental specifications for the physical SVP supplied by Hitachi Vantara.

Item

Specification

Operating temperature

41°F ~ 95°F

(5°C ~ 35°C)

Non-operating temperature range

-40°F ~ 140°F

(-40°C ~ 60°C)

Operating relative humidity range

8% ~ 90% (non-condensing)

Non-operating relative humidity range

5% - 95% (non-condensing)